15 . Things That Your Boss Wished You Knew About Niceic Domestic Installer

Descrição

Electricity Meter Installation – http://www.gawonsilver.com/bbs/board.php?bo_table=carte&wr_id=23587

Electric meters are a great tool to track your electricity usage. They can also help you reduce your power bills!

They are usually an encased metering device made of glass that resembles a large mason Jar. They come with five dials and an enormous rotating wheel that measures the amount of kilowatt hours of electricity.

The Feeder Side

The feeder component of an electricity meter installation is most important aspect for homeowners because it is a part of the overall electrical service. This area of the meter base is where the power from the utility company is connected to the meter and the wires connecting it to the remainder of your home’s electrical system. This is where you’ll find your most obvious wire connections: hot, neutral and ground. The best thing is that the utility company will usually provide the meter as well as the necessary wiring. However, you are accountable for putting it all together.

To put together the top-quality meter base, you’ll need a couple of the aforementioned items, meter box – http://selectstarfromsql.com/index.php/question/10-high-voltage-installation-tricks-experts-recommend/ as well as a hefty helping of anti-corrosion compounds to shield your wires from damage by the elements. The most important thing you need to do is determine the meter’s orientation (left or right hand front) and then measure the length of the three wires you intend on attaching to it. The most effective method for doing this is to make use of a telescoping measuring tape make sure to wear a pair of gloves.

The Load Side

The load side of an electricity meter installation is where the electrical feed leaves the meter and is taken to the main service panel. This feed can be from a single breaker or multiple circuit breakers located in the main panel. The connection for the load is typically placed at the lower two load terminals on the meter’s hot bus bars but it could be done with an interim disconnect (See Figure 3 phase electrical installation – http://cse.google.co.nz/url?sa=i&url=http%3A%2F%2Fwww.electricians-r-us.co.uk%2Felectrical-installations%2F).

The conduit that runs from the service wires to the meter must be the conduit. It must be situated in a location that isn’t blocked by furniture or other obstructions. It must be at least two feet (2′) from any exposed wiring on the side that is used for load and connected to the base of the meter with an entrance cap on top of the conduit (see figure 16).

Unless LES is in agreement with a different method wires shouldn’t be run through conduit. The conduit should be accessible to Company representatives to read meters and test.

The base of the meter must be securely mounted to the brick’s studs, concrete block or the equivalent. If the meter will be mounted on vinyl, metal or wood lap siding the backing of 3/4 inch thick outdoor plywood should be utilized. It should be placed on a level surface and straight. It should be put in a position where it is easily accessible by Company representatives for meter reading and testing, as well as maintenance.

Grounding Wire

The installation of electricity meters includes a grounding wire to protect the home from the effects of excess electricity. If an over-voltage or short circuit electrical current is generated and the grounding wire is damaged, it can help to safely discharge the electricity from the home and keep it from flowing back to the mains.

The grounding wire connects to the earth outside your home in two ways. It can be connected to a copper waterpipe or an 8-foot long ground rod is inserted into the soil.

When the grounding wire isn’t grounded, excessive electrical current can escape through other pathways into your home damaging appliances and meter box – http://youngpoongwood.com/bbs/board.php?bo_table=inquire&wr_id=55953 electronics or a potential house fire. It is important to know the causes of these issues and how they can be dealt with to avoid them.

The prongs are a great way to check if your outlets have been grounded. Outlets that are grounded have three slots while ungrounded outlets have just two slots. The ground wire is the one that is connected to the d-shaped slots below the parallel slots.

Because the earth beneath your feet is negative charges that draws electrical currents there. Ground wires are designed to allow these positive charges to be able to locate a safe spot so they don’t get energized, which can cause trouble.

If your electric meter has not installed or repaired after a while you should call your utility company. They’ll be able to verify that it was properly grounded. To ensure that it’s operating properly an electrician with a license should inspect the meter.

When you’re deciding on an electrician to install your new meter, be aware that they must follow the rules and regulations set by your local utility com